Two-stage compression
Lower stage compression ratio, reduced internal leakage and bearing load, higher volumetric efficiency and longer host life.
{{ variable.name }}
For rubber and plastics plants with high-temperature, dusty and continuous-production workshops. Two-stage PM VSD is applied to injection molding, blow molding, molding and demolding equipment where energy cost and pressure stability matter.

In rubber and plastics plants, injection molding and blow molding machines are high-energy consumers. This two-stage PM VSD air compressor is used for steady air supply and significant energy savings on energy-intensive lines. Two-stage compression lowers the stage ratio and thermal load, while PM VSD adjusts speed to changing demand. High-pressure PET bottle blowing at 35–40 bar is a separate high-pressure compressor requirement.
Lower stage compression ratio, reduced internal leakage and bearing load, higher volumetric efficiency and longer host life.
Two-stage PM VSD replaces single-stage compression and increases displacement by nearly 15%, adding up to 15% energy saving.
Applied to high-energy equipment such as injection molding and blow molding machines for significant energy savings.
Compared with ordinary industrial frequency machines. At 8,000 h/year, the saving can reach about USD 30,000 per year.
The motor and male rotor use one shaft, eliminating coupling and gear transmission and reducing related failure risk.
No motor, bearing, gear or coupling noise; noise range for the series is 65–78 ±3 dB.
| Parameter | Specification |
|---|---|
| Model family | SLTT-22V, SLTT-30V, SLTT-37V, SLTT-45V, SLTT-55V, SLTT-75V, SLTT-90V, SLTT-110V, SLTT-132V, SLTT-160V, SLTT-185V, SLTT-220V, SLTT-250V |
| Working pressure | 8–13 bar |
| Capacity | 1.36–53.68 m³/min (series range) |
| Power range | 22–250 kW |
| Horsepower | 30–335 hp |
| Noise | 65–78 ±3 dB |
| Air outlet pipe diameter | DN40, DN50, DN65, DN100 |
| Net weight | 732–6000 kg (series range) |
| Compression | Two-stage compression |
| Drive | Permanent magnet variable frequency drive |
| Rotor profile | Patented UV profile, refined by more than 20 procedures |
| Materials | Cast iron, stainless steel |
The SLTT-V series covers 13 models from SLTT-22V to SLTT-250V, with 22–250 kW power, 8–13 bar working pressure and 1.36–53.68 m³/min capacity range. Final model selection depends on required air flow, pressure, duty cycle and site conditions.
The air end uses a patented UV rotor profile and two-stage compression structure. Cast iron and stainless steel are used in the construction. The PM VSD motor and male rotor adopt an integrated shaft structure, so there is no coupling or gear transmission. This compact arrangement reduces efficiency loss and mechanical failure points.
Low noise and low vibration are achieved by removing motor, bearing, gear and coupling noise sources. The integrated PM VSD structure also saves floor space, which matters in high-temperature, dusty rubber and plastics workshops.
This two-stage PM VSD unit is used in rubber and plastics plants for stable, efficient air supply:
Sollant supports OEM/ODM customization. Project requirements can be discussed around the SLTT-V model, working pressure within 8–13 bar, air outlet size, and matched refrigerated dryer or precision filter configuration. Sollant was founded in 2004 and operates a 30,000 ㎡ facility with 20,000 units annual output.
Injection molding and blow molding machines are high-energy consumers. Two-stage compression reduces the stage ratio and thermal load, while PM VSD matches speed to demand. The rubber and plastics solution targets 15%–40% energy savings on energy-intensive lines.
Two-stage PM VSD can increase displacement by nearly 15% and save up to 40% versus ordinary industrial frequency machines. For high-energy injection and blow molding equipment, the application scenario targets 15%–40% savings.
No. This SLTT-V series covers 8–13 bar working pressure. High-pressure PET bottle blowing at 35–40 bar is handled by a separate high-pressure screw air compressor in the plant solution.
The rubber and plastics solution matches refrigerated air dryers and precision filters (C/T grade) to remove moisture and oil, helping prevent air bubbles, shrinkage and other quality defects in plastic products.
The SLTT-V series includes SLTT-22V, SLTT-30V, SLTT-37V, SLTT-45V, SLTT-55V, SLTT-75V, SLTT-90V, SLTT-110V, SLTT-132V, SLTT-160V, SLTT-185V, SLTT-220V and SLTT-250V.
Sollant's related certification set includes CE for air compressors, CE for permanent magnet motors, EMC for the controller, PED verification for oil and air tanks, and ISO 14001 environmental management.
Yes. OEM/ODM support is available, and Sollant provides 24/7 engineering after-sales support and original spare parts through its international service team.
Send your required model, working pressure, capacity, site conditions and destination country to info@sollant.com. Tel or WhatsApp: +86 155-8905-3798. Address: No.215, Songri Center, Beihongqiao, Jiading District, Shanghai, China.
Discuss Your Molding Project