menú

4x2 Road Sweeper Truck with 2.2 m Sweeping Width and 45,000 m2/h Coverage

en stock:
SKU: 2723381692
modelo: Road Sweeper Truck

{{ variable.name }}

{{ value.name }}

4x2 Road Sweeper Truck with 2.2 m Sweeping Width and 45,000 m2/h Coverage

Product summary. A 4x2 truck-mounted mechanical sweeper that combines centre-mounted twin disc brushes, a wide floating vacuum suction nozzle and high-pressure spray bars at the brushes and at the nozzle. Published production figures for this unit are 7,360 kg GVW, 2,190 kg payload, 2.2 m sweeping width, 1 m3 water tank, 2 m3 dust bin, 45,000 m2/h working area and 95 percent or higher sweeping efficiency. It suits municipal routes where a 7,000-10,000 kg GVW chassis stays inside local axle and bridge limits.

4x2 road sweeper truck sweeping a city street with the spray bar active

Road sweeper truck in 4x2 city configuration, disc brushes lowered and spray bar running.

Key Selling Points

Dust bound before the brush landsHigh-pressure spray bars at the brushes and at the suction nozzle wet the road first, and the sealed dust bin keeps the load inside - the practical answer to fine-dust complaints on residential streets.
2.2 m adjustable sweeping widthSingle-side or dual-side operation lets the operator narrow the pass for tight lanes and widen it on open carriageways.
Retractable kerb brushFitted on the left, on the right or on both sides, so gutters and kerbs are cleaned in the same pass as the carriageway.
Air-duct conversionRecirculation or direct suction mode lets the truck keep working in dry season, after rain and on wet leaves instead of standing idle.
Hydraulic brush driveBrush rotation speed is adjustable to the surface - slower on rough asphalt, faster on loose sand.
Published output figures45,000 m2/h working area at 95 percent or higher sweeping efficiency on a standard test surface, so daily routes can be planned against measured coverage.

Technical Specifications

ItemSpecification
Drive configuration4x2
GVW7,000-10,000 kg (published unit 7,360 kg)
Rated payload2,000-12,000 kg range (published unit 2,190 kg)
Sweeping width2.2-3.6 m adjustable (2.2 m on the published unit)
Working area20,000-90,000 m2/h (45,000 m2/h on the published unit)
Sweeping efficiency95% or higher on a standard test surface
Water tank / dust bin1-10 m3 / 2-12 m3 (1 m3 and 2 m3 on the published unit)
Maximum particle diameter100-150 mm at the suction nozzle
Working / transport speed3-20 km/h / 90-100 km/h
EngineDiesel 85-250 kW, Euro II to Euro V, matched to local fuel quality
Auxiliary engine57-100 kW, dedicated to the suction fan and hydraulic pump
Water pumpHigh-pressure piston or centrifugal, 8-15 MPa for washing
Bin dischargeRear tipping or rear door, 20-40 s per cycle
Gradeability / noise20-30% / below 82 dB(A) at 7 m in normal sweeping mode
Working temperature-20 to +50 degrees C; tropical cooling or cold-start package available
Cab and drive side2-3 persons day cab, left-hand or right-hand drive

Models and Options

Water tank volume is selectable from 1 to 10 m3 and dust bin volume from 2 to 12 m3, so the same platform can be re-quoted with a larger hopper or a second axle. The kerb brush can be specified on the left, the right or both sides. Engines run from 85 to 250 kW in Euro II to Euro V with a manual 5-10 speed gearbox or an automated manual as an option. Left-hand and right-hand drive are both built, and a tropical cooling package or a cold-start package can be fitted. Optional equipment includes a fog cannon, a separate washing boom, a hand-held spray gun and a drinking-water tank.

Materials and Structure

Body and tanks are built in Q235/Q345 carbon steel, shot-blasted, epoxy-primed and polyurethane topcoated, with stainless steel 304 used for the water tank and dust bin where humidity or salt is a problem. The dust bin floor and discharge door are 4-6 mm wear-resistant steel and the sub-frame is 6-8 mm bolted. Brushes use polypropylene or nylon filament discs with replaceable segments and optional steel-wire tufts for heavy debris. The suction nozzle is Q345 wear-resistant steel with replaceable rubber or polyurethane wear strips, and EPDM rubber seals sit on tank covers, doors and nozzle skirts.

Applications

  • Municipal sanitation and street cleaning on residential and arterial roads
  • Industrial estates, logistics parks and parking areas
  • Residential compounds, squares and commercial plazas
  • Campus, hospital and industrial-estate roads
  • Toll stations, weighbridges and bus terminals

Customization

Configuration is fixed before quotation by asking what road is swept, what debris is typical, how many kilometres a day, whether water is available on site and where the bin is tipped. Those answers set tank volume, sweeping width, brush layout and axle configuration, so the truck is neither too small for the route nor too heavy for the road.

FAQ

What are the published figures for the 4x2 unit?7,360 kg GVW, 2,190 kg payload, 2.2 m sweeping width, 1 m3 water tank, 2 m3 dust bin, 45,000 m2/h working area and 95 percent or higher sweeping efficiency.
Can the tanks be enlarged?Yes. Water tank from 1 to 10 m3 and dust bin from 2 to 12 m3 are available, and the truck is re-quoted on the same platform.
How is dust controlled?High-pressure spray bars at the brushes and at the suction nozzle wet the surface before the brush touches it, and the sealed rear-tipping dust bin keeps the load inside.
Can it sweep after rain?Yes. The air-duct conversion switches between recirculation and direct suction for dry, wet or rainy-day operation.
What is the lead time and how does the unit ship?About 25-40 working days from down payment, under FOB, CIF or DAP terms by RoRo or break-bulk, 1-4 units per shipment, with invoice, packing list, bill of lading, certificate of origin and insurance issued as one set.
What testing and warranty are included?Every unit is checked before shipment for brush rotation, suction performance, spray pressure, hydraulic pressure, bin tipping, brake and road test. Major components carry a 12-month warranty; wear parts such as brushes, nozzle strips and seals are excluded.

Inquiry Information

Send the road type, the typical debris, daily kilometres, whether a water filling point is available and where the bin is emptied, and the configuration is quoted against those answers.

Tel +86-13083602803  |  WhatsApp +86-16638078903  |  Email info@elorry-ind.com

Supplier factory qualification assessed by SGS under the Alibaba Gold Plus Supplier Assessment Criteria, certificate 479886222_T, valid to 06 Nov 2026.

Image Filename and Alt Suggestions

  • road-sweeper-truck-4x2-city-front.png - 4x2 road sweeper truck with disc brushes lowered on a city street
  • road-sweeper-truck-4x2-kerb-brush.png - retractable kerb brush cleaning a gutter beside the suction nozzle
  • road-sweeper-truck-4x2-bin-tipping.png - rear-tipping dust bin discharging at a tipping point
SEO title: 4x2 City Road Sweeper Truck with 2.2 m Sweep and 1 m3 Water TankMeta description: 4x2 city road sweeper truck with 2.2 m sweeping width and 1 m3 water tank. Twin disc brushes, 2 m3 dust bin, 45,000 m2/h working coverage, 7,360 kg GVW.URL slug: /4x2-city-road-sweeper-truckKeywords: 4x2 road sweeper truck, city street sweeper truck, vacuum road sweeper, kerb sweeping truck