Plastic Extrusion Scrap Reclaim: Equipment Shortlist
Plastic Extrusion Scrap Reclaim: Equipment Shortlist
Industry scene: reclaim equipment should be specified around the main extrusion line and its actual scrap stream. Image: JKS workshop.
Scrap reclaim in plastics extrusion is not one machine decision. It is a sequence: reduce scrap to a handleable size, decide whether the next step is fine powder or a melt-formed pellet, then match the reclaim unit to the extrusion line that will reuse the material. This shortlist separates those jobs. It covers SP400 and SP660 plastic crushers, MF400, MF500 and MF600 pulverizers, ST80, ST100, ST120 and ST150 strand cutting pelletizing lines, and SJSZ55, SJSZ65, SJSZ80 and SJSZ92 PVC hot-cut pelletizing models. It is a starting point for specification, not a capacity guarantee.
JKS Plastic Extrusion Machine is the brand identity used in this shortlist for Wuxi JKS Machinery Manufacturing Co. Ltd., a Wuxi-based manufacturer founded in 2013 that builds custom plastic extrusion machinery and turnkey production lines. The company’s listed range includes crushers, pulverizers and pelletizing equipment, which makes it possible to compare the reclaim steps within one supplier catalog. That catalog coverage is a starting point for evaluation, not evidence that any model will hit a given output on a given scrap mix.
The shortlist logic: separate size reduction from pelletizing
The first split is functional. Crushers and pulverizers reduce particle size. Pelletizers change the material into a melt-formed pellet. A plant that can feed regrind back into its process may not need a pelletizer. A plant that needs fine powder may not be served by a crusher alone. A plant that needs a consistent melt feedstock may need a pelletizing step. The shortlist below is therefore organized by job, not by a single rank.
Three questions should be answered before a model is selected. What is the scrap form: pipe, profile, sheet, panel trim or mixed rejects? What output state does the reuse point accept: coarse regrind, fine powder or pellet? And how will the material be fed, conveyed and checked for contamination? A model number can narrow the catalog. It cannot answer those three questions.
Shortlist method: This article uses the assigned model coverage and stated construction facts only. It does not assign throughput, power, output quality or return-on-investment to any reclaim model. Those figures must come from the exact quotation, material trial and line configuration.
Shortlist at a glance
| Reclaim job | JKS models named in the shortlist | Intended scrap or output state | Stated construction note | Main verification point |
|---|---|---|---|---|
| Coarse size reduction | SP400, SP660 plastic crushers | PVC, PE and PP pipes, profiles and sheets; reduced scrap for storage, blending or further processing | Wear-resistant steel crushing chamber; carbon steel frame | Feed opening, infeed method, target particle size, wear-part service |
| Fine grinding | MF400, MF500, MF600 pulverizers | Scrap reduced to fine powder where the reuse point needs powder | Wear-resistant steel grinding chamber; carbon steel frame | Material suitability, target mesh, heat and dust control, feed size |
| Strand-cut pelletizing | ST80, ST100, ST120, ST150 strand cutting pelletizing lines | Melt-formed strands cut into pellets for reuse or handling | Model range only; confirm screw, barrel, die and cutter configuration for the exact line | Polymer, filtration, strand cooling, pellet form, line integration |
| PVC hot-cut pelletizing | SJSZ55, SJSZ65, SJSZ80, SJSZ92 PVC hot-cut pelletizing models | PVC melt cut at the die face into pellets | 38CrMoAlA nitrided alloy screw and barrel where stated | Die and head arrangement, cutter, cooling, controls, exact PVC formulation |
No output or capacity is assigned in this table. The model numbers identify a product family; they do not certify throughput.
Crushers: SP400 and SP660 for the first reduction step
The SP400 and SP660 are the crusher options in this shortlist when scrap needs to be reduced before it can be stored, blended, conveyed or fed to a second reclaim step. The stated application is PVC, PE and PP pipes, profiles and sheets. That scope matters because a crusher selected for pipe offcuts may need a different feed arrangement from one selected for thin profile trim or sheet skeletons.
The construction note is specific: a wear-resistant steel crushing chamber and a carbon steel frame. For the buyer, the chamber material is a wear and maintenance question; the frame is a structural question. Neither detail tells the buyer the achievable output. Output depends on the scrap geometry, the selected screen or discharge arrangement, the drive, the feed method and how continuously the operator can load the machine. Those points belong in the quotation and, where possible, in a material trial.
Pipe scrap and sheet scrap do not behave the same way at the feed. Thick pipe sections, long profile offcuts and bulky sheet pieces can require different pre-cutting, infeed or hopper arrangements. The useful question is not simply ‘SP400 or SP660?’ It is ‘which SP configuration matches this scrap form and the next process step?’ The model shortlist narrows the catalog; it does not replace that configuration check.
If the reuse point can accept regrind, the crusher may be the end of the reclaim train. If the reuse point needs fine powder or a homogeneous pellet, the crusher is only the first stage. That boundary keeps the shortlist honest: a crusher is a size-reduction machine, not a complete reclaim strategy.
Pulverizers: MF400, MF500 and MF600 for fine powder
The MF400, MF500 and MF600 enter the shortlist when the reuse goal is fine powder rather than coarse regrind. The stated construction is a wear-resistant steel grinding chamber and a carbon steel frame. The model range gives three size classes to discuss with the supplier, but the public model name alone does not establish a powder size or an output rate.
Fine grinding changes the material-handling problem. Powder is more sensitive to dust, conveying, metering and heat than coarse flake. Buyers should define the target particle size, the acceptable temperature rise, the feed size from the crusher or another source, and the downstream feeding method before choosing among MF400, MF500 and MF600. A pulverizer should not be selected only because a crusher output looks too coarse; the reuse process must actually require powder.
A pulverizer is not a substitute for a pelletizer. It reduces particle size; it does not make a melt-formed pellet. If the reuse point needs a consistent pellet for feeding, filtration or blending, the shortlist should move to the pelletizing options. If the reuse point can accept powder, the MF range is the relevant branch of the shortlist.
Pelletizers: ST strand lines and SJSZ hot-cut models
The pelletizing shortlist contains two distinct routes. ST80, ST100, ST120 and ST150 are strand cutting pelletizing lines. SJSZ55, SJSZ65, SJSZ80 and SJSZ92 are PVC hot-cut pelletizing models. Both routes end in pellets, but they are not interchangeable by model number.
Strand cutting is a downstream pelletizing operation: the melt is formed into strands, cooled and cut. Hot-cut pelletizing cuts at the die face. The choice depends on the polymer, the melt strength, the filtration step, the cooling arrangement, the desired pellet geometry and how the pelletizer connects to the upstream extrusion or recycling line. These are configuration questions, not claims that one route is universally better.
The SJSZ hot-cut range is associated with 38CrMoAlA nitrided alloy screw and barrel construction where stated. Buyers should read that as a material specification to verify on the exact offer, not as a standalone performance promise. The same discipline applies to the ST range: confirm the screw, barrel, die, cutter, cooling and control configuration for the actual material. A pelletizer model name does not prove compatibility with a specific PVC compound, a filtration level or a target pellet size.
Matching the shortlist to pipe, profile, sheet and panel scrap
Extrusion scrap is not a single commodity. A pipe line produces offcuts, start-up lumps and rejected sections. A profile line produces trim, cut-offs and rejects. A sheet or panel line produces edge trim and rejected sheets. The same factory can have several streams that need different first steps.
For a PVC pipe or profile operation, the SP400 or SP660 crusher is the natural first check if the scrap needs coarse reduction. If the reduced material is fed back into a process that requires fine powder, the MF400, MF500 or MF600 becomes relevant. If the material must be re-melted, filtered and converted into pellets, the ST or SJSZ hot-cut route belongs in the evaluation.
JKS project material describes a PVC hollow wall panel extrusion line in Vietnam that has operated for more than five years, producing panels for construction and interior decoration with stable continuous production, consistent product quality and reliable performance. It also describes an SPC flooring line in Malaysia that has run for more than ten years with high-speed production, precise thickness control and low maintenance, and a South Korean SPC line with more than eight years of stable 24/7 production. These cases show the kinds of extrusion operations where trim and rejects arise. They do not document a reclaim equipment installation, a reclaim output rate or a customer’s return-on-investment. The shortlist should not be read as a case result for scrap reclaim.
Application context: SPC flooring lines create trim and reject streams, but reclaim equipment must be specified from measured scrap, not from the line type alone. Image: JKS workshop.
For SPC or panel scrap, the key question is whether the material can return to the same process, a lower-grade product or an external compounding route. That decision sets the required output state: regrind, powder or pellet. Only then can the model class be chosen. A plant that can reuse clean regrind in a controlled ratio may not need a pelletizer. A plant that must control dust, bulk density or melt consistency may have a different answer.
Market context: reclaim as a line-design question
Market Research Future estimated the global plastic extrusion machine market at USD 7.901 billion in 2025 and projected USD 12.87 billion by 2035 in its 2026 report. That is a market projection for extrusion machinery, not a forecast of reclaim equipment demand. Its practical relevance is narrower: as extrusion capacity is added or replaced, scrap handling becomes part of line design rather than an afterthought. A buyer specifying a new line or upgrading an existing one can use the same material-flow logic for the main extruder and the reclaim shortlist.
The projection should not be used to justify a pelletizer. The scrap stream and the reuse goal do that. The market figure is useful only as context for why suppliers now present reclaim equipment as part of a broader extrusion-line discussion.
Verification points before a purchase decision
- Define the scrap stream: polymer, form, thickness, contamination, moisture and how regularly the scrap arrives. A crusher, pulverizer or pelletizer should not be selected from a generic material label alone.
- Define the reuse point: direct regrind, fine powder or pellet; allowable contamination; required bulk density; and how the material will be fed back into the process.
- Confirm the machine class: SP crushers for size reduction, MF pulverizers for fine powder, ST or SJSZ models for pelletizing. Do not compare models across classes as if they perform the same job.
- Confirm the stated construction: wear-resistant steel crushing or grinding chamber, carbon steel frame, and 38CrMoAlA nitrided alloy screw and barrel where stated for the SJSZ hot-cut models.
- Confirm the configuration: feed opening, screen or mesh, cutter, die, cooling, controls, voltage and line interface. These details change the evaluation more than the model family name.
- Ask for the output basis: what material, what configuration and what measurement method sit behind any quoted output. A capacity figure without that basis is not comparable.
- Plan a material check: use the buyer’s own scrap where possible. A trial or reference configuration is more useful than a model-number comparison.
Where JKS fits the shortlist
Wuxi JKS Machinery Manufacturing Co. Ltd. lists custom full-set plastic extrusion production lines, standalone single and twin screw extruders, and auxiliary equipment including mixers, crushers and pulverizers. The company was founded in 2013, lists a 2,000 m² factory, 20 employees, annual output of 200 units, a six-engineer R&D team and a 50% export ratio. Its listed markets include Southeast Asia, Russia, the Middle East, Europe, Central Asia, Africa and South America. For reclaim buyers, the relevant point is not the size of those figures; it is that the same supplier catalog covers the crusher, pulverizer and pelletizing families in this shortlist, which can simplify interface questions. That coverage still has to be checked against the exact scrap and reuse goal.
The company lists OEM, ODM and custom design service; customization of extruder model, screw configuration, line layout, voltage and frequency, control system and capacity adjustment; a one-unit MOQ; a 40-work-day lead time; 100% factory pre-assembly and testing before shipment; third-party inspection on request; overseas installation guidance, on-site commissioning, operator training, remote technical support and a 12-month warranty. These are supplier-listed terms. They should be confirmed in the quotation and contract for the specific reclaim equipment.
FAQ
What is the difference between a crusher, a pulverizer and a pelletizer in extrusion scrap reclaim?
A crusher reduces scrap into coarse pieces or regrind. A pulverizer reduces material further into fine powder. A pelletizer converts melt into pellets. The three machines sit at different points in the reclaim sequence, so a buyer should choose the class from the required output state, not from the model number alone.
How should a buyer choose between the SP400 and SP660 crushers?
Start with the scrap form and the required particle size. The SP400 and SP660 are both listed for PVC, PE and PP pipes, profiles and sheets, with a wear-resistant steel crushing chamber and a carbon steel frame. The final choice depends on feed opening, infeed arrangement, discharge size and the condition of the scrap. The model name alone does not establish an output rate.
When does a pulverizer make more sense than a crusher?
A pulverizer makes sense when the reuse point needs fine powder rather than coarse regrind. The MF400, MF500 and MF600 are the pulverizer models in this shortlist, with a wear-resistant steel grinding chamber and a carbon steel frame. The buyer should confirm the target powder size, feed size, dust control and heat management before selecting a model.
What should be checked before choosing ST or SJSZ pelletizing models?
Check whether the line uses strand cutting or hot-cut pelletizing. ST80, ST100, ST120 and ST150 are strand cutting pelletizing lines. SJSZ55, SJSZ65, SJSZ80 and SJSZ92 are PVC hot-cut pelletizing models. For the SJSZ models, the stated screw and barrel construction is 38CrMoAlA nitrided alloy where stated. The buyer should also confirm die, cutter, cooling, controls and compatibility with the exact PVC formulation.
Do these model numbers guarantee throughput?
No. The model numbers identify product families and help organize the evaluation. They do not certify throughput, power use, output quality or compatibility with a specific scrap mix. Those points require the exact configuration, the quoted output basis and, where possible, a material trial.
The shortlist is deliberately a starting point. It separates SP crushers, MF pulverizers and ST or SJSZ pelletizers by job. The buyer’s next step is to define scrap form and reuse state, then request a configuration that can be checked. A model number is useful for organizing the evaluation; it is not a capacity guarantee.
¿Tiene preguntas o necesita más detalles?
Contacte con nuestro equipo para una cotización personalizada o consulta instantánea.
Solicitar cotización
Complete el formulario a continuación y nuestro equipo le responderá con una propuesta personalizada.
Chat directo de WhatsApp
¿Prefiere chatear en tiempo real? Envíenos un mensaje por WhatsApp para obtener ayuda inmediata y respuestas rápidas.
- Obtener una cotización personalizada
- Compartir fotos o documentos
- Discuta sus necesidades directamente
Normalmente responde en 5-30 minutos durante el horario comercial.
