PGM, AUX, Multiview, UVC: A Production Switcher Framework
PGM, AUX, Multiview, UVC: A Production Switcher Framework
Output planning starts with the destination, not with the mixing surface.
Production switcher tenders usually open with inputs, mix effects and panel layout. The evaluation that fails later often fails on outputs. Program, auxiliary, multiview and USB Video Class (UVC) feeds travel to different destinations, and each destination carries its own format, cable and host expectations. A switcher that mixes cleanly but cannot address the required destinations in the right signal class turns into a rack of converters, distribution amplifiers and support calls.
This framework works backwards from those destinations. It uses the output set of the TCHD-840 Super — 2×12G-SDI PGM, 2×12G-SDI AUX, 1×3G-SDI PGM down-convert, 1×HDMI 2.0 PGM, 1×DP multiview and 1×UVC — as a worked example, and sets out the questions a Decision-stage buyer should answer before issuing a purchase order.
Why output planning comes before feature comparison
Three questions decide whether an output set is adequate: where the program must go, what operators must see while it goes there, and what must be captured or streamed alongside it. Answer those three in writing and the shortlist usually narrows itself, because most mismatches are structural rather than technical.
Converters can solve almost any output mismatch. The cost is not the converter alone. Each unit adds a power outlet, a rack position, a configuration someone must document, and a failure point that tends to appear during the show rather than before it. When the native output count already matches the destination count, that entire layer disappears from the signal chain and from the maintenance budget.
Format class matters as much as port count. 12G-SDI, 3G-SDI, HDMI 2.0, DisplayPort and UVC are not interchangeable carriers; each has a different reach, connector and host expectation. The buyer's task is to match the carrier to the destination, not to collect the largest number of connectors on the rear panel.
The four output roles, defined
- PGM (program). The program output carries the switched, on-air composite — the feed the audience is meant to see. It is the output that must survive the show.
- AUX (auxiliary). An auxiliary output is independently assignable. It can carry a clean feed, a second-language version, an isolated source, or a signal for a screen or archive, without changing what the audience sees.
- Multiview. A multiview output is a monitoring composite: several sources, usually with program and preview, arranged on one screen for the operator. It is an operational tool, not a delivery feed.
- UVC. USB Video Class is a USB device class. A switcher exposing a UVC output presents its feed to a connected computer as a camera-class device, so software can select it as a video source without a separate capture card.
Keeping these roles separate prevents a common procurement error: specifying a multiview or a UVC feed as though it were a program output. One serves the operator, one serves software, and neither replaces a baseband program feed to a router or a transmitter.
TCHD-840 Super: the output set as a decision map
TCHD Video (TCHD Digital Video Technology Development (Beijing) Ltd) is a Beijing-based video hardware manufacturer established in 2005, with a 10,000 m² facility, 50 employees, an annual output of 4,000 units and a 10-engineer R&D team. The company's role in this discussion is narrow: it supplies a concrete output list that a buyer can test against real destinations.
| Output | Signal class | Typical destination | Buyer question it answers |
|---|---|---|---|
| 2× 12G-SDI PGM | 12G-SDI | Production router, UHD record, primary transmission | Can the main program reach two high-bandwidth destinations natively? |
| 2× 12G-SDI AUX | 12G-SDI | Clean feed, second-language feed, large screen, archive | Is an independently assignable 12G feed required outside program? |
| 1× 3G-SDI PGM down-convert | 3G-SDI (HD-class) | Legacy HD router, HD transmission, confidence feed | Must the same program reach HD-only equipment without a converter? |
| 1× HDMI 2.0 PGM | HDMI 2.0 | In-room display, desktop recorder, streaming appliance | Is there a short-run destination outside the SDI plant? |
| 1× DP multiview | DisplayPort | Operator monitor | Can one operator see all sources plus program and preview at once? |
| 1× UVC | USB Video Class | Laptop or PC running software encoders, conferencing or capture software | Can the feed reach software without a capture card? |
Two entries in that list carry more weight than the total port count. The program path is duplicated at 12G-SDI, and SMPTE ST 2082 defines 12G-SDI as uncompressed 4K at 60 fps over a single coaxial cable at a nominal 11.88 Gbps (Samim Group, 2025). For the buyer, two 12G program outputs mean the router and a primary record or transmission path can each be fed directly, without an external splitter deciding what happens if one leg fails.
The 3G-SDI program output is explicitly a down-convert. 3G-SDI is an HD-class carrier, so this port exists to reach HD infrastructure — a legacy router, an HD transmitter chain, an HD confidence feed — from the same program source, without adding a converter box. It is a bridge between a high-bandwidth program and an installed base that has not yet been replaced.
The HDMI 2.0 and DisplayPort outputs cover the two ends of a facility that baseband broadcast planning often ignores: a local display or desktop recorder on HDMI, and the operator's monitoring screen on DisplayPort. The single UVC output is the software bridge, and it is the port that most often decides whether a streaming or lecture-capture workflow needs additional hardware.
A six-step decision framework
- List destinations, not devices. Write down every place the picture must appear: router, transmitter, record, screen, operator monitor, software encoder. A device can serve two destinations; a destination cannot be served by a port that does not exist.
- Assign a format class to each destination. Mark which destinations are 12G-capable, which are HD-only, which accept HDMI, and which need a computer to see the feed as a camera.
- Count program-path outputs first. Program is the feed that must not fail. If two independent program destinations exist, two native program outputs are a requirement rather than a convenience.
- Decide whether AUX is a requirement or an option. A clean feed for archive, a second language, or a screen showing something other than program turns AUX from a nice-to-have into a specification line.
- Budget monitoring separately. A multiview output reduces the number of monitors and the number of people needed in the room; treat it as an operational cost item, not as a delivery output.
- Test the software-facing output on the actual host. UVC behaviour depends on the operating system, the application and the USB controller in the machine that will run the show.
Broadcast workflows: baseband first
In a broadcast chain, the 12G-SDI program outputs do the delivery work. One leg typically feeds the production router or the transmission path; the second can feed a primary record or a backup route. The 12G AUX outputs then handle everything that must leave the switcher without appearing on air: a clean feed for a rights holder, a second-language version, or a screen feed for a stage.
Consider a regional broadcaster upgrading the studio to UHD while the station router remains HD. The 12G program output serves the new chain; the 3G-SDI down-convert keeps the HD router and the HD confidence feed supplied from the same program source. The limitation is one of scale rather than capability: a single down-converted output covers a single HD destination, so a plant with several HD destinations still needs distribution. The buyer should count HD destinations before treating the down-convert as a complete solution.
Streaming workflows: software decides the format
Streaming rarely needs a dedicated hardware encoder at the switcher any more. A UVC output lets the production computer select the switcher as a camera source, and the software handles encoding, bitrate and platform delivery. That arrangement suits multi-platform distribution, because the platform logic lives where it can be updated, not inside the switcher chassis.
The commercial pressure behind this pattern is measurable. Livestream e-commerce is projected to reach USD 312.35 billion by 2035, with Asia Pacific holding a 66% share as of 2025 (Precedence Research, 2026). Buyers in that segment — church services, esports qualifiers, lecture capture, product-launch streams — usually own a computer already and want the switcher to disappear into it as one more selectable source. A UVC port satisfies that expectation; an SDI-only switcher forces a capture card into the budget and into the troubleshooting path.
The fit boundary is worth stating plainly. One UVC output serves one host. Multi-destination streaming is a software function in this configuration, not a switcher function, and the resolution, frame rate and compression the host actually receives should be confirmed on that machine rather than assumed from the switcher's baseband specifications.
Recording and archive: separate the clean feed
Recording is where output assignment quietly becomes an editorial decision. A program record captures the show as the audience saw it, graphics and all. A clean-feed record captures the switched sources without overlays, which is what post-production, rights archives and highlight edits usually need. The 12G AUX outputs exist precisely for the second case: an assignable feed that follows the production without duplicating the graphics layer.
The HDMI 2.0 program output covers a different tier — a desktop recorder, a review monitor in the green room, or a small streaming appliance. HDMI is generally a short-run interface, so cable length and signal equalization should be planned rather than improvised. For a fixed installation this is manageable; for a temporary event build it is worth checking before the truck is loaded.
Where a converter still wins, and where it does not
External converters and distribution amplifiers remain the correct answer in several situations: more than two independent 12G destinations, a large HD plant with many downstream points, or a need to bridge to a format the switcher does not expose at all. In those cases the converter extends a sound design rather than rescuing a bad one.
The 12G AUX outputs exist precisely for the second case...
¿Tiene preguntas o necesita más detalles?
Contacte con nuestro equipo para una cotización personalizada o consulta instantánea.
Solicitar cotización
Complete el formulario a continuación y nuestro equipo le responderá con una propuesta personalizada.
Chat directo de WhatsApp
¿Prefiere chatear en tiempo real? Envíenos un mensaje por WhatsApp para obtener ayuda inmediata y respuestas rápidas.
- Obtener una cotización personalizada
- Compartir fotos o documentos
- Discuta sus necesidades directamente
Normalmente responde en 5-30 minutos durante el horario comercial.
